REVEALING THE ABRASION RESISTANCE OF META-STABLE TITANIUM ALLOYS USING MULTI-PASS DUAL-INDENTER TESTS
Keywords:
titanium alloy, abrasion resistance, scratch test, microstructure
Abstract
The abrasion resistance of the Ti-5Al-4Zr-4Mo-2Cr-2Sn-1Fe alloy was investigated using multi-pass dual-indenter (MPDI) scratch tests with different loading conditions under a repetitive local sliding contact. Various microstructures were obtained with different heat treatments. The effect of the phase morphology on the scratch resistance and corresponding failure mechanisms were revealed. Results show that the phase morphology has a great influence on the scratch resistance and that the effect is contact-load dependent. The scratch behaviour is linked to the initial surface hardness at low loading conditions, while the work-hardening ability is more relevant at high loading conditions.
References
1 W. Chen, A. Yan, C. Wang, Y. Deng, D. C. Chen, H. Xiao, D. Zhang, X. Meng, Microstructures and mechanical properties of AlCrN/ TiSiN nanomultilayer coatings consisting of fcc single-phase solid solution, Applied Surface Science, 509 (2020), 145303, doi:10.1016/j.apsusc.2020.145303
2 C. Li, L. Qin, M. Li, H. Xiao, Q. Wang, J. Chen, Influence of deformation strain rate on the mechanical response in a metastable titanium alloy with various microstructures, Journal of Alloys and Compounds, 815 (2020), 152426, doi:10.1016/j.jallcom.2019.152426
3 W. Chen, T. Hu, C. Wang, H. Xiao, X. Meng, The effect of micro¬structure on corrosion behavior of a novel AlCrTiSiN ceramic coating, Ceramics International, 46 (2020), 12584–12592, doi:10.1016/ j.ceramint.2020.02.022
4 C. Li, M. Li, H. Li, J. Chen, H. Xiao, Influence of solution treatment on microstructural evolution and mechanical properties of a new titanium alloy, Kovove Materials, 58 (2020), 41–48, doi:10.4149/km_ 2020_1_41
5 H. Schimdt, A. Schminke, M. Schmiedgen, B. Baretzky, Compound formation and abrasion resistance of ion-implanted Ti6Al4V, Acta Materialia, 49 (2001), 487–495, doi:10.1016/S1359-6454(00) 00326-8
6 T. Sawase, K. Yoshida, Y. Taira, K. Kamada, M. Atsuta, K. Baba, Abrasion resistance of titanium nitride coatings formed on titanium by ion-beam-assisted deposition, Journal of Oral Rehabilitation, 32 (2005), 151–157, doi:10.1111/j.1365-2842.2004.01382.x
7 Y. Zhu, W. Wang, X. Jia, T. Akasaka, S. Liao, F. Watari, Deposition of TiC film on titanium for abrasion resistance implant material by ion-enhanced triode plasma CVD, Applied Surface Science, 262 (2012), 156–158, doi:10.1016/j.apsusc.2012.03.152
8 K. Farokhzadeh, A. Edrisy, Transition between mild and severe wear in titanium alloys, Tribology International, 94 (2016), 98–111, doi:10.1016/j.triboint.2015.08.020
9 G. Subhash, W. Zhang, Investigation of the overall friction coefficient in single-pass scratch test, Wear, 252 (2002), 123–134, doi:10.1016/S0043-1648(01)00852-3
10 A. Vencl, N. Manic, V. Popovic, M. Mrdak, Possibility of the abrasive wear resistance determination with scratch tester, Tribology Letters, 37 (2010), 591–604, doi:10.1007/ s11249-009-9556-x
11 X. Xu, S. van der Zwaag, W. Xu, Prediction of the abrasion resistance of construction steel on the basis of the subsurface deformation layer in a multi-pass dual-indenter scratch test, Wear, 338–339 (2015), 47–53, doi:10.1016/j.wear.2015.05.012
12 I. P. Semenova, R. R. Valiev, K. S. Selivanov, Y. M. Modina, A. V. Polyakov, M. K. Smyslova, R. Z. Valiev, Enhanced strength and scratch resistance of ultra-fine grained Ti64 alloy with (Ti+V)N coating, Review of Advanced Materials Science, 48 (2017), 62–70, http://www.ipme.ru/e-journals/RAMS/no_14817/05_14817 _valiev.pdf
13 K. Holmberg, A. Laukkanen, H. Ronkainen, J. Li, W. Beres, Three-¬dimensional finite element modelling of the scratch test for a TiN coated titanium alloy substrate, Wear, 260 (2006), 1232–1242, doi:10.1016/j.wear.2005.08.008
14 X. Xu, S. van der Zwaag, W. Xu, A novel multi-pass dual-indenter scratch test to unravel abrasion damage formation in construction steels, Wear, 322–323 (2015), 51–60, doi:10.1016/j.wear. 2014.10.011
15 C. Li, H. Li, S. van der Zwaag, Unravelling the abrasion resistance of two novel meta-stable titanium alloys on the basis of multi-¬pass-dual-indenter test, Wear, 400–441 (2019), 203094, doi:10.1016/j.wear.2019.203094
2 C. Li, L. Qin, M. Li, H. Xiao, Q. Wang, J. Chen, Influence of deformation strain rate on the mechanical response in a metastable titanium alloy with various microstructures, Journal of Alloys and Compounds, 815 (2020), 152426, doi:10.1016/j.jallcom.2019.152426
3 W. Chen, T. Hu, C. Wang, H. Xiao, X. Meng, The effect of micro¬structure on corrosion behavior of a novel AlCrTiSiN ceramic coating, Ceramics International, 46 (2020), 12584–12592, doi:10.1016/ j.ceramint.2020.02.022
4 C. Li, M. Li, H. Li, J. Chen, H. Xiao, Influence of solution treatment on microstructural evolution and mechanical properties of a new titanium alloy, Kovove Materials, 58 (2020), 41–48, doi:10.4149/km_ 2020_1_41
5 H. Schimdt, A. Schminke, M. Schmiedgen, B. Baretzky, Compound formation and abrasion resistance of ion-implanted Ti6Al4V, Acta Materialia, 49 (2001), 487–495, doi:10.1016/S1359-6454(00) 00326-8
6 T. Sawase, K. Yoshida, Y. Taira, K. Kamada, M. Atsuta, K. Baba, Abrasion resistance of titanium nitride coatings formed on titanium by ion-beam-assisted deposition, Journal of Oral Rehabilitation, 32 (2005), 151–157, doi:10.1111/j.1365-2842.2004.01382.x
7 Y. Zhu, W. Wang, X. Jia, T. Akasaka, S. Liao, F. Watari, Deposition of TiC film on titanium for abrasion resistance implant material by ion-enhanced triode plasma CVD, Applied Surface Science, 262 (2012), 156–158, doi:10.1016/j.apsusc.2012.03.152
8 K. Farokhzadeh, A. Edrisy, Transition between mild and severe wear in titanium alloys, Tribology International, 94 (2016), 98–111, doi:10.1016/j.triboint.2015.08.020
9 G. Subhash, W. Zhang, Investigation of the overall friction coefficient in single-pass scratch test, Wear, 252 (2002), 123–134, doi:10.1016/S0043-1648(01)00852-3
10 A. Vencl, N. Manic, V. Popovic, M. Mrdak, Possibility of the abrasive wear resistance determination with scratch tester, Tribology Letters, 37 (2010), 591–604, doi:10.1007/ s11249-009-9556-x
11 X. Xu, S. van der Zwaag, W. Xu, Prediction of the abrasion resistance of construction steel on the basis of the subsurface deformation layer in a multi-pass dual-indenter scratch test, Wear, 338–339 (2015), 47–53, doi:10.1016/j.wear.2015.05.012
12 I. P. Semenova, R. R. Valiev, K. S. Selivanov, Y. M. Modina, A. V. Polyakov, M. K. Smyslova, R. Z. Valiev, Enhanced strength and scratch resistance of ultra-fine grained Ti64 alloy with (Ti+V)N coating, Review of Advanced Materials Science, 48 (2017), 62–70, http://www.ipme.ru/e-journals/RAMS/no_14817/05_14817 _valiev.pdf
13 K. Holmberg, A. Laukkanen, H. Ronkainen, J. Li, W. Beres, Three-¬dimensional finite element modelling of the scratch test for a TiN coated titanium alloy substrate, Wear, 260 (2006), 1232–1242, doi:10.1016/j.wear.2005.08.008
14 X. Xu, S. van der Zwaag, W. Xu, A novel multi-pass dual-indenter scratch test to unravel abrasion damage formation in construction steels, Wear, 322–323 (2015), 51–60, doi:10.1016/j.wear. 2014.10.011
15 C. Li, H. Li, S. van der Zwaag, Unravelling the abrasion resistance of two novel meta-stable titanium alloys on the basis of multi-¬pass-dual-indenter test, Wear, 400–441 (2019), 203094, doi:10.1016/j.wear.2019.203094
Published
2021-06-02
How to Cite
1.
Xiao H, Huang C, Chen J, Li C. REVEALING THE ABRASION RESISTANCE OF META-STABLE TITANIUM ALLOYS USING MULTI-PASS DUAL-INDENTER TESTS. MatTech [Internet]. 2021Jun.2 [cited 2025Jan.19];55(3):435–442. Available from: https://mater-tehnol.si/index.php/MatTech/article/view/182
Section
Articles
