EFFECT OF NITROGEN ON THE THERMAL DEFORMATION BEHAVIOR OF MARTENSITIC STAINLESS BEARING STEEL
Keywords:
martensitic stainless bearing steel, thermal deformation behavior, power dissipation diagram, thermal deformation activation energy, thermal processing diagram
Abstract
The thermal deformation behaviors of martensitic stainless bearing steels (0.16N, 0N) in the temperature range 850–1150 °C, strain rate 0.01–10 s–1, and deformation of 60 % were studied using a single-pass compression experiment. After adding 0.16 % nitrogen, the peak stress of the martensitic stainless bearing steel increased under all thermal forming conditions, and the average peak stress increased by about 33.724 MPa. The strain-rate sensitivity diagram, power dissipation diagram, instability factor diagram, and thermal processing diagram under different strains were constructed based on the stress-strain curve. The thermal deformation activation energy under different strains was constructed and combined with a metallographic structure analysis. The results show that under the same conditions, the occurrence of DRX in 0.16N bearing steel is less than that of 0N bearing steel, but the grains are finer than those of 0N bearing steel.
References
1 F. Yu, X.P. Chen, H.F. Xu, H. Dong, Y.Q. Weng, W.Q. Cao, Current Status of Metallurgical Quality and Fatigue Performance of Rolling Bearing Steel and Development Direction of High-End Bearing Steel, Acta Metall. Sin., 56 (2020) 4, 513-522, doi: 10.11900/0412.1961.2019.00361
2 R. Wang, F.H. Li, Z.Q. Yu, Y. Kang, M. Li, Y. Hu, H.R. An, J. Fan, F. Miao, Y.H. Zhao, J. Eckert, Z.J. Yan, Influences of partial substitution of C by N on the microstructure and mechanical properties of 9Cr18Mo martensitic stainless steel, Mater. Des., 236 (2023), doi: 10.1016/j.matdes.2023.112497
3 M. Seifert, S. Siebert, S. Huth, W. Theisen, H. Berns, New Developments in Martensitic Stainless Steels Containing C plus N, Steel Res. Int, 86 (2015) 12, 1508-1516, doi: 10.1002/srin.201400503
4 S.J. Zheng, J.H. Liu, L. Xu, S.M. Wen, Z.H. Han, Hot deformation behavior of high nitrogen martensitic stainless steels, Mater. Res. Express, 6 (2019) 1, doi: 10.1088/2053-1591/aae5e8
5 H. Feng, Z.H. Jiang, H.B. Li, W.C. Jiao, X.X. Li, H.C. Zhu, S.C. Zhang, B.B. Zhang, M.H. Cai, Hot Deformation Behavior and Microstructural Evolution of High Nitrogen Martensitic Stainless Steel 30Cr15Mo1N, Steel Res. Int., 88 (2017) 12, doi: 10.1002/srin.201700149
6 X. Li, L.F. Hou, Y.H. Wei, Z.Y. Wei, Constitutive Equation and Hot Processing Map of a Nitrogen-Bearing Martensitic Stainless Steel, METALS, 10 (2020) 11, doi: 10.3390/met10111502
7 W.J. Liu, J. Li, S.H. Li, J.H. Li, X.J. Li, Effect of Nitrogen on the Hot Deformation Behavior of 0.4C-13Cr Martensitic Stainless Steel, Steel Res. Int., 92 (2021) 8, doi: 10.1002/srin.202100020
8 Z.G. Nie, G. Wang, J.C. Yu, D.H. Liu, Y.M. Rong, Phase-based constitutive modeling and experimental study for dynamic mechanical behavior of martensitic stainless steel under high strain rate in a thermal cycle, Mech. Mater., 101 (2016), 160-169, doi: 10.1016/j.mechmat.2016.08.003
9 J.Y. Zhang, Y. Tang, H.M. Zhou, Q. Chen, J. Zhou, Y. Meng, Investigation on thermal rheological behavior and processing map of 30CrMnSiNi2A ultra-strength steel, Int. J. Mater. Form., 14 (2021) 4, 507-521, doi: 10.1007/s12289-019-01531-1
10 W. Feng, F. Qin, H. Long, Hot workability analysis and processing parameters optimisation for 20CrMnTiH steel by combining processing map with microstructure, IRONMAKING & STEELMAKING, 45 (2018) 4 , 317-324, doi: 10.1080/03019233.2016.1264145
11 H.A. Lin, M.S. Yang, B. Song, Study on hot compressive deformation behavior and microstructure evolution of G13Cr4Mo4Ni4V steel, Mater. Today Commun., 38 (2024), doi: 10.1016/j.mtcomm.2024.108429
12 Y.C. Zhu, Q.H. Wang, Z.Q. Huang, L. Qin, Z.L. Li, L.F. Ma, Strain Hardening Exponent and Strain Rate Sensitivity Exponent of Cast AZ31B Magnesium Alloy, METALS, 12 (2022) 11, doi: 10.3390/met12111942
13 L. Chen, B. Zhang, Y. Yang, T.L. Zhao, Y. Xu, Q. Wang, B. Zan, J. Cai, K.S. Wang, X. Chen, Evolution of hot processing map and microstructure of as-forged nickel-based superalloy during hot deformation, J. Mater. Res. Technol., 24 (2023), 7638-7653, doi: 10.1016/j.jmrt.2023.05.060
14 J. Luo, M.Q. Li, Efficiency of Power Dissipation and Instability Criterion for Processing Maps in Hot Forming, CMC-Comput. Mater. Continua, 18 (2010) 3, 271-299
15 L. Han, H.Y. Zhang, J. Cheng, G. Zhou, C. Wang, L.J. Chen, Thermal Deformation Behavior of Ti-6Mo-5V-3Al-2Fe Alloy, CRYSTALS, 11 (2021) 10, doi: 10.3390/cryst11101245
16 H.Y. Qin, Z.T. Li, G.P. Zhao, W.Y. Zhang, Q. Tian, C. Wang, Hot Deformation Behavior and Microstructure and Mechanical Properties Evolution of Forged GH4742 Superalloy, Rare Met. Mater. Eng., 51 (2022) 11, 4227-4236
17 Y.H. Song, Z.H. Cai, G.H. Zhao, Y.G. Li, H.Y. Li, M.X. Zhang, Hot deformation behavior of 309L stainless steel, Mater. Today Commun., 36 (2023), doi: 10.1016/j.mtcomm.2023.106877
18 L.X. Li, B. Ye, S. Liu, S.D. Hu, B. Li, Inverse analysis of the stress-strain curve to determine the materials models of work hardening and dynamic recovery, Mater. Sci. Eng., A, 636 (2015), 243-248, doi: 10.1016/j.msea.2015.03.115
19 L.X. Ouyang, R. Luo, Y.W. Gui, Y. Cao, L.L. Chen, Y.J. Cui, H.K. Bian, K. Aoyagi, K. Yamanaka, A. Chiba, Hot deformation characteristics and dynamic recrystallization mechanisms of a Co-Ni-based superalloy, Mater. Sci. Eng., A, 788 (2020), doi: 10.1016/j.msea.2020.139638
20 T. Masumura, T. Tsuchiyama, S. Takaki, T. Koyano, K. Adachi, Difference between carbon and nitrogen in thermal stability of metastable 18%Cr-8%Ni austenite, Scr. Mater., 154 (2018), 8-11, doi: 10.1016/j.scriptamat.2018.05.019
2 R. Wang, F.H. Li, Z.Q. Yu, Y. Kang, M. Li, Y. Hu, H.R. An, J. Fan, F. Miao, Y.H. Zhao, J. Eckert, Z.J. Yan, Influences of partial substitution of C by N on the microstructure and mechanical properties of 9Cr18Mo martensitic stainless steel, Mater. Des., 236 (2023), doi: 10.1016/j.matdes.2023.112497
3 M. Seifert, S. Siebert, S. Huth, W. Theisen, H. Berns, New Developments in Martensitic Stainless Steels Containing C plus N, Steel Res. Int, 86 (2015) 12, 1508-1516, doi: 10.1002/srin.201400503
4 S.J. Zheng, J.H. Liu, L. Xu, S.M. Wen, Z.H. Han, Hot deformation behavior of high nitrogen martensitic stainless steels, Mater. Res. Express, 6 (2019) 1, doi: 10.1088/2053-1591/aae5e8
5 H. Feng, Z.H. Jiang, H.B. Li, W.C. Jiao, X.X. Li, H.C. Zhu, S.C. Zhang, B.B. Zhang, M.H. Cai, Hot Deformation Behavior and Microstructural Evolution of High Nitrogen Martensitic Stainless Steel 30Cr15Mo1N, Steel Res. Int., 88 (2017) 12, doi: 10.1002/srin.201700149
6 X. Li, L.F. Hou, Y.H. Wei, Z.Y. Wei, Constitutive Equation and Hot Processing Map of a Nitrogen-Bearing Martensitic Stainless Steel, METALS, 10 (2020) 11, doi: 10.3390/met10111502
7 W.J. Liu, J. Li, S.H. Li, J.H. Li, X.J. Li, Effect of Nitrogen on the Hot Deformation Behavior of 0.4C-13Cr Martensitic Stainless Steel, Steel Res. Int., 92 (2021) 8, doi: 10.1002/srin.202100020
8 Z.G. Nie, G. Wang, J.C. Yu, D.H. Liu, Y.M. Rong, Phase-based constitutive modeling and experimental study for dynamic mechanical behavior of martensitic stainless steel under high strain rate in a thermal cycle, Mech. Mater., 101 (2016), 160-169, doi: 10.1016/j.mechmat.2016.08.003
9 J.Y. Zhang, Y. Tang, H.M. Zhou, Q. Chen, J. Zhou, Y. Meng, Investigation on thermal rheological behavior and processing map of 30CrMnSiNi2A ultra-strength steel, Int. J. Mater. Form., 14 (2021) 4, 507-521, doi: 10.1007/s12289-019-01531-1
10 W. Feng, F. Qin, H. Long, Hot workability analysis and processing parameters optimisation for 20CrMnTiH steel by combining processing map with microstructure, IRONMAKING & STEELMAKING, 45 (2018) 4 , 317-324, doi: 10.1080/03019233.2016.1264145
11 H.A. Lin, M.S. Yang, B. Song, Study on hot compressive deformation behavior and microstructure evolution of G13Cr4Mo4Ni4V steel, Mater. Today Commun., 38 (2024), doi: 10.1016/j.mtcomm.2024.108429
12 Y.C. Zhu, Q.H. Wang, Z.Q. Huang, L. Qin, Z.L. Li, L.F. Ma, Strain Hardening Exponent and Strain Rate Sensitivity Exponent of Cast AZ31B Magnesium Alloy, METALS, 12 (2022) 11, doi: 10.3390/met12111942
13 L. Chen, B. Zhang, Y. Yang, T.L. Zhao, Y. Xu, Q. Wang, B. Zan, J. Cai, K.S. Wang, X. Chen, Evolution of hot processing map and microstructure of as-forged nickel-based superalloy during hot deformation, J. Mater. Res. Technol., 24 (2023), 7638-7653, doi: 10.1016/j.jmrt.2023.05.060
14 J. Luo, M.Q. Li, Efficiency of Power Dissipation and Instability Criterion for Processing Maps in Hot Forming, CMC-Comput. Mater. Continua, 18 (2010) 3, 271-299
15 L. Han, H.Y. Zhang, J. Cheng, G. Zhou, C. Wang, L.J. Chen, Thermal Deformation Behavior of Ti-6Mo-5V-3Al-2Fe Alloy, CRYSTALS, 11 (2021) 10, doi: 10.3390/cryst11101245
16 H.Y. Qin, Z.T. Li, G.P. Zhao, W.Y. Zhang, Q. Tian, C. Wang, Hot Deformation Behavior and Microstructure and Mechanical Properties Evolution of Forged GH4742 Superalloy, Rare Met. Mater. Eng., 51 (2022) 11, 4227-4236
17 Y.H. Song, Z.H. Cai, G.H. Zhao, Y.G. Li, H.Y. Li, M.X. Zhang, Hot deformation behavior of 309L stainless steel, Mater. Today Commun., 36 (2023), doi: 10.1016/j.mtcomm.2023.106877
18 L.X. Li, B. Ye, S. Liu, S.D. Hu, B. Li, Inverse analysis of the stress-strain curve to determine the materials models of work hardening and dynamic recovery, Mater. Sci. Eng., A, 636 (2015), 243-248, doi: 10.1016/j.msea.2015.03.115
19 L.X. Ouyang, R. Luo, Y.W. Gui, Y. Cao, L.L. Chen, Y.J. Cui, H.K. Bian, K. Aoyagi, K. Yamanaka, A. Chiba, Hot deformation characteristics and dynamic recrystallization mechanisms of a Co-Ni-based superalloy, Mater. Sci. Eng., A, 788 (2020), doi: 10.1016/j.msea.2020.139638
20 T. Masumura, T. Tsuchiyama, S. Takaki, T. Koyano, K. Adachi, Difference between carbon and nitrogen in thermal stability of metastable 18%Cr-8%Ni austenite, Scr. Mater., 154 (2018), 8-11, doi: 10.1016/j.scriptamat.2018.05.019
Published
2024-12-05
How to Cite
1.
SongY, Lu Y, Li Y, SunH, Li H, XuH, WangY. EFFECT OF NITROGEN ON THE THERMAL DEFORMATION BEHAVIOR OF MARTENSITIC STAINLESS BEARING STEEL. MatTech [Internet]. 2024Dec.5 [cited 2026Oct.11];58(6):809–818. Available from: https://mater-tehnol.si/index.php/MatTech/article/view/1194
Section
Articles
